![\"P1020674.JPG\"](\"https:\/\/carson.fenimorefamily.com\/wp-content\/uploads\/2015\/08\/P1020674.JPG.jpg\")
<\/a><\/p>\nSince this was my first woodworking project there was a fair amount of ramup.\u00a0 I dedicated myself to the study of Norm Abram, watching as many New Yankee Workshop episodes as the Internet would yield unto me.<\/p>\n
Step 1: Pedestal<\/strong><\/p>\n The\u00a0 process begin by pulling up the carpet and built a small platform of 2x4s.\u00a0 This platform was needed to bring the shelves up high enough so the baseboard moulding could run under the shelves and connect up with the moulding on the connecting walls.<\/p>\n Step 2: Carcasses<\/strong><\/p>\n Essentially the carcass is the cabinet \/ bookshelf – it forms the entire structure.\u00a0 Virtually everything else is cosmetic.\u00a0 This surprised me because people charge a ton for furniture work, but essentially you are just building boxes.\u00a0 How’s that for a deprecating simplification of cabinet making!<\/p>\n Another surprise has to do with the building material.\u00a0 Whenever I hear people talk about furniture it is clear that quality and hardwood are synonymous.\u00a0 Yet all the guidlines for building furniture involve plywood.\u00a0 How could this be?\u00a0 It turns out plywood is stronger – much stronger – than using plain old hardwood.\u00a0 And far less expensive.\u00a0 I think I got my sheets of plywood for around $60 each.\u00a0 The bulk of the cabinets were built for around $500 total!<\/p>\n One thing you appreciate from watching Norm Abram and others is joinery.\u00a0 There are all kinds of ways to bind two peices of wood together: pocket screws, dowels, rabbet, mortise and tenon, etc.\u00a0 I chose to join the carcasses with double rabbet joints.\u00a0 To do this I bought a\u00a0Diablo Dado Kit<\/a>\u00a0 for the table saw.\u00a0 I passed the plywood edges through to take away half the width on each side.\u00a0 I then glued the sides, held them in place with pipe clamps, and screwed them together.\u00a0 As Norm would often say, the screws are not really there to hold the thing together – just to keep it from moving while the glue dried.\u00a0 I think they do add strength, but they’re not the main source.<\/p>\n On that note, may i say: wood glue is amazing stuff.\u00a0 I used a variety of glues: basically Tightbond II and Gorilla Glue.\u00a0 Im not sure if Tightbond III would have made a difference – in looking at the bond strength, Tightbond II and III seemed about equal.\u00a0 Essentially you’d have to be the incredible hulk to separate two fully-cured bonded pieces of wood.\u00a0 The Gorilla Glue is also a\u00a0 good option, but I didn’t find it any better (but it was more expensive).<\/p>\n Another amazing tool: the table saw.\u00a0\u00a0 Its the main tool to use in woodworking.\u00a0 A few table saw truths now resonate with me:<\/p>\n To complete the boxes I glued in some 1\/4″ plywood into a rabbet I had made to the back of the boxes (before joining them).<\/p>\n That brings me to my two main regrets about the carcasses:<\/p>\n As can be seen below, I formed four carcases: 1) The left cabinet, with 1\/3 of the window seat attached, 2) the left bookshelf, placed atop the left cabinet, 3) the right cabinet, and 4) the right bookshelf, also placed atop the right cabinet.\u00a0 This left the middle section, which I finished after screwing the bookshelves to the pedestal.\u00a0\u00a0 To make that work, before bringing the caracses in I formed a rabbet on both the top and bottom edges of the window seat portions of the cabinet.\u00a0 I also formed rabbets on two pieces of plywood.\u00a0 I then slide one of the peices on the bottom of the middle area, and nailed it to the pedestal.\u00a0 The other one went on top.<\/p>\n When this was all done I put another sheet of plywood on top of the window seat, to cover up the seams on the layer below.\u00a0 \u00a0 When that was done I basically had the following:<\/p>\n <\/p>\n Step 3: Facade <\/strong><\/p>\n I think they call this the face plate.\u00a0 Its the only part that is actually solid hardwood.\u00a0 I chose 3\/4″ white oak from home depot.\u00a0 It was fairly expensive – I’d say I spent at least as much on the faceplate as all the caracases, if not more.<\/p>\n I joined the faceplate using mortise and tenons.\u00a0 I am proud to say I made a single faceplate for the bottom half that went from the left side of the room to the right .<\/p>\n To form the joints I used the table saw to form the tenons.\u00a0 I used a drill press to form the mortises.\u00a0 One note on that:\u00a0 I bought a fairly cheap drill press, but it worked very well.\u00a0 It just took a long time.\u00a0 I investigated using mortising drill bits, however these really didnt make a ton of sense – the idea is they chisle as you go down.\u00a0 Well, maybe that makes sense, but in the end the drill worked just fine.<\/p>\n Of course I applied copious glue in joining the mortise and tenon joints.\u00a0 I also bought some pipe clamps to hold them in place as they dried.\u00a0 A note on that: it is really important to let the glue dry in a warm room.\u00a0 I tried doing it in the cold garage and found it didn’t dry at all.\u00a0 I guess you have to follow the manufacturers recommendations – who knew!<\/p>\n I placed glue along the back of the faceplate and used finishing nails to hold it in place to the carcass.\u00a0 Note again the nails really just hold it in place while the glue dries.<\/p>\n I also formed solid hardwood table tops for the bookshelves. Im not entirely sure why I did this.\u00a0 Those things could hold a tank: two layers of 3\/4″ plywood with a 3\/4″ layer of hardwood.<\/p>\n Step 4: Shelves and Doors<\/strong><\/p>\n The shelves are brain-dead easy.\u00a0 I took plywood and cut some hardwood strips as a faceplate.\u00a0 I then glued the faceplate to the hardwood, using a few finishing nails.\u00a0 I filled the nail holes with putty.\u00a0 Oh, and I did round the hardwood (before affixing it to the plywood) using some rounding bits on my router table.<\/p>\n As for the doors, this was the fancy part – the one that requires precision.\u00a0 You have three elements to each door: stiles, rails, and panels.\u00a0 The rails are the top part of the frame, the stiles are the sides, and the panel fills the middle.<\/p>\n For the panel I joined together three\u00a0 6″ slabs of oak.\u00a0 If I were Norm, and had his setup, I would have used a joiner to make sure the edges of the plywood were perfectly flat.\u00a0 I don’t have joiner, but the stuff from Home Depot seemed pretty flat.\u00a0 So I glued it together and clamped it tightly with some pipe clamps.<\/p>\n I then carefully measured, remeasured, marked the size of the panels.\u00a0 It turns out you want the panel to float a bit inside of the rails\/stiles.\u00a0 You do this to allow for expansion in the panel.\u00a0 The wood grain of the panel runs vertically.\u00a0 Wood tends to expand with the grain, so the panels are supposed to be cut such that there is about 1\/8″ wiggle room on each side.\u00a0 Wood does not expand much against the grain, so only 1\/16″ wiggle room is needed.<\/p>\n Cutting the panels wasn’t tricky, but it was a bit time consuming.\u00a0 This is because I wanted to avoid ruining my router as it chomped through really thick wood with a big bit.\u00a0 So i took two or three passes, each time getting closer and closer to the router bit.\u00a0\u00a0 I did end up burning the wood a bit on one panel, as can be seen below.<\/p>\n A note on router tables: I bought the Bench Dog<\/a> router table from Amazon.\u00a0 I was torn on this purchase – there were so many high quality expansive options.\u00a0 For example, I would have loved to have one with a precise lift mechanism. In the end I think it would have saved time, but the cheap bench worked very well.\u00a0 My only real regret with it was the size – it was hard to do these panels, as the bench couldnt support them.<\/p>\n Another note on improvising: The fun part of woodworking is being able to make anything.\u00a0 Along the way, you have to make jigs and guides.\u00a0 I think I made several for this project, including my own cross-cut sled for the table saw.\u00a0 When i went to use the panel router, for example, i found it didn’t fit through the hole of the one that came with the router bench.\u00a0 So i made my own!\u00a0 It worked just fine.<\/p>\n Step 5: Staining and Finish<\/strong><\/p>\n There were lots of other little steps, including forming a two-layer crown moulding along the top, but within a few months I was ready to stain things.\u00a0\u00a0 I tried to sand everything well with a palm sander.\u00a0 We then decided to use a darker stain, partly because it actually looked nice, partly because i wanted to cover up some of my mistakes.<\/p>\n This part was actually fairly easy – i just applied a lot of stain, then wiped it off.\u00a0 I did that twice or so in most cases, except on the hardwood where i had to do it three times or so.<\/p>\n My main regret here is not protecting the carpet.\u00a0 I should have covered it with a thick drop cloth.\u00a0 But i didnt, and of course ended up getting the carpet in several places.<\/p>\n Another note on stain: to make it more even, some people recommend using a diluted laqueer or pre-stain treater.\u00a0 That might have been a great idea, but it made things too light for my likes.\u00a0 Maybe next time.<\/p>\n Once the stain was dry (i gave it the recommended week or two) I applied a varnish.\u00a0 I did two layers almost everywhere – three or four layers on high-impact areas like the window seat.<\/p>\n <\/p>\n <\/p>\n The first picture in this post is the best picture I\u00a0have of the\u00a0finished product.\u00a0 Note there is some kind of a posterboard sitting atop the cabinet on the right – that’s not the crown moulding.\u00a0 Pretty nice for a first timer!<\/p>\n","protected":false},"excerpt":{"rendered":" Last winter or so we decided to build bookshelves. \u00a0 After much pondering we decided to make them built into the wall and have a window seat.\u00a0\u00a0 Here’s what we came up with (we never really got a good picture of it before leaving to the EC): Since this was my first woodworking project there … Continue reading Builtin Bookshelves<\/span> \n
\n
<\/a> <\/a> <\/a><\/p>\n<\/a> <\/a> <\/a><\/p>\n<\/a><\/p>\n